Waterproof electronics encapsulation with hot melt works by molding a thermoplastic, usually a polyamide, around the board, sensor or connector so that it bonds to every surface water could follow; the IP rating you reach, such as IP67 or IP68, is set by the finished part and its weakest leak path, not by the adhesive alone. That distinction matters in design reviews. A material datasheet can tell you about adhesion, water absorption and temperature range, but an IP rating is a test result for a specific enclosure. This article explains what IP codes mean, where water typically gets into hot melt encapsulated parts, and the design and test steps that make a seal hold up over time.
Key points
- An IP code has two digits: the first for solid particles (up to 6, dust-tight) and the second for water (up to 8 in IEC 60529, with 9K defined for road vehicles in ISO 20653).
- Most leaks in hot melt encapsulated parts start at an interface: the cable jacket, the connector housing or along the strands inside a wire.
- Seal performance should be checked after thermal cycling and aging, because a part that passes when new can leak after temperature changes.
What an IP rating actually tells you
The IP (Ingress Protection) code is defined in IEC 60529. It describes how well an enclosure keeps out solid objects and water, using two digits after the letters "IP". The first digit runs from 0 to 6; 5 means dust-protected and 6 means dust-tight. The second digit runs from 0 to 8 in the core standard and describes water exposure that grows more severe as the number rises: dripping, spraying, splashing, jets, powerful jets, temporary immersion and continuous immersion. For road vehicles, ISO 20653 adds IPX9K, which covers high-pressure, high-temperature spray cleaning.
| Rating | Water exposure (general) | Typical relevance |
|---|---|---|
| IPX5 / IPX6 | Water jets / powerful jets | Outdoor housings, wash-down areas |
| IPX7 | Temporary immersion, typically about 1 m for 30 min | Sensors, handheld devices, connectors |
| IPX8 | Continuous immersion beyond IPX7, conditions agreed | Submersible sensors, pumps |
| IPX9K | High-pressure, high-temperature spray (ISO 20653) | Vehicle underbody and engine bay parts |
Two practical points follow. First, higher is not automatically "better": an immersion rating such as IPX7 does not by itself prove resistance to water jets, so parts that see both are often tested and marked for both (for example IP66/IP67). Second, IPX8 has no single fixed test; the depth and duration must be stated by the manufacturer. When a specification simply says "IP68", ask for those conditions.
Why hot melt is used to waterproof electronics
Electronics can be protected against water in several ways: conformal coating, potting in a housing, gaskets and separate enclosures, or low pressure molding with hot melt. Each has a place, and the options are compared in PCB Encapsulation Options: Conformal Coating, Potting and Low Pressure Molding. Hot melt low pressure molding is chosen when a part needs a sealed, robust body formed in one step:
- Short cycle: the molten material is injected at low pressure and solidifies as it cools, so there is no long curing time as with two-part potting compounds.
- Gentle on components: the low injection pressure is generally compatible with soldered components and fine wires.
- Housing and seal together: the molded body acts as the enclosure, the strain relief and the seal, which can remove a separate housing and gasket.
- Solvent-free: the material is a solid thermoplastic, so there are no solvents to evaporate.
Polyamide hot melts are commonly used here because they combine adhesion to many plastics and metals with heat resistance and flexibility. The trade-off is that the seal depends on bonding, so design and process control matter more than with a mechanical gasket.
Waterproof electronics encapsulation with hot melt: where water gets in
Water rarely passes through the bulk of a well-molded polyamide body. It gets in at the boundaries. Mapping those boundaries is the first design step for waterproof electronics encapsulation with hot melt.
Common leak paths in hot melt sealed electronics
| Leak path | Why it fails | Design response |
|---|---|---|
| Cable jacket | Poor bond to jacket | Check adhesion, treat surface |
| Wire strands | Water wicks inside | Seal stripped conductors |
| Connector body | Release agent, mismatch | Clean, match materials |
| Pins and inserts | Gaps after cycling | Longer bond, even walls |
General examples; actual leak paths depend on the part design.
- Cable jacket interface: the molding material must bond to the jacket compound. Some jacket materials, especially low-surface-energy or heavily plasticized grades, are harder to bond and may need surface treatment or a different jacket.
- Inside the wire (wicking): even with a perfect seal on the jacket, water can travel along the gaps between stranded conductors and enter the part from inside. Sealing the conductors where the jacket is stripped, so the melt flows between strands, helps block this path.
- Connector and housing interfaces: when the molding is overmolded onto a pre-molded connector body, the bond to that plastic decides the seal. Matching the hot melt to the housing material and cleaning release agents from the surface are key.
- Inserts and pins: metal pins, screws and inserts contract differently from the polymer around them, which can open gaps after temperature changes.
Design tips for a reliable seal
The following tips apply to most hot melt sealed electronics. They do not replace testing, but they remove the common causes of failure before the first sample run.
- Give the seal length: a longer bonded path along the cable jacket or housing gives water a longer route and spreads stress. Very short overlap areas are a frequent source of leaks.
- Keep walls even: uniform wall thickness reduces sink marks and voids. Sudden thick sections cool slowly and can shrink away from inserts. Practical molding causes and fixes are covered in Troubleshooting Low Pressure Molding: Voids, Short Shots, Flash and Poor Adhesion.
- Plan gates and vents: trapped air at a critical interface becomes a leak path. Place vents where the melt front meets last and fix inserts so they do not move during injection; see Low Pressure Molding Mold Design: Gates, Venting and Insert Fixing.
- Prepare surfaces: oils, flux residues and mold release agents prevent bonding. Define a cleaning step and, where needed, a surface treatment for difficult plastics.
- Control material moisture: polyamide hot melts absorb moisture from the air. Wet material can foam or bond poorly, so keep bags sealed and follow the supplier's storage guidance.
- Design for strain relief: cable movement concentrates stress at the exit point of the molding. A tapered strain relief reduces peeling at that interface; see Low Pressure Molding for Wire Harnesses and Cable Strain Relief.
Testing: from material data to an IP test
A reliable path from material choice to an IP claim usually runs through three levels of testing.
- Material screening: adhesion of candidate hot melts to the actual jacket, housing and board materials, measured on test pieces. Water absorption and temperature range from the datasheet narrow the list.
- Part-level conditioning: molded parts go through thermal cycling, humidity exposure or vibration that represent service. Temperature changes are the most common reason seals open, as discussed in Adhesives for High-Stress Environments: Vibration, Thermal Cycling and Chemicals.
- IP test of the finished part: after conditioning, parts are tested to IEC 60529 (or ISO 20653 for vehicle parts) at the rating required. Many teams also use pressure-decay or leak tests on the production line to catch individual defects.
Testing new parts alone can give a false sense of security. A part that passes an immersion test straight off the molding machine may fail after a few hundred temperature cycles. Running the IP test after conditioning gives a much more realistic answer.
SILVERSTAR CHEMICAL and polyamide for low pressure molding
SILVERSTAR CHEMICAL Co., Ltd. has produced its own polyamide hot melts since 2011 and supplies them under the ERAMID brand. For low pressure molding, ERAMID solvent-free polyamides are used to encapsulate PCBs, sensors, connectors and wire harnesses.
- Grades: UL 94 V-0 flame-retardant grades and grades with thermal stability up to 200°C are available, with shorter cycle times than potting.
- Formulation: VOC- and halogen-free formulations with high bond strength and heat and chemical resistance.
- In-house manufacturing: raw material selection, formulation and quality inspection are done in-house, and custom viscosity and formulation development can be discussed. The company holds ISO 9001 and ISO 14001 certification.
Adhesion data for specific jacket or housing materials and other test documentation are provided on inquiry. See the low pressure molding solution page, the automotive solution page and the SILVERSTAR CHEMICAL company FAQ for more.
Frequently Asked Questions
Q. Can hot melt be used for waterproof electronics encapsulation?
Yes. Waterproof electronics encapsulation with hot melt is usually done by low pressure molding, where a polyamide hot melt is injected around a PCB, sensor or connector at low pressure and solidifies in seconds to form a sealed housing. Whether the part reaches a given IP rating depends on adhesion to every material in the assembly, the part design and testing of the finished part, not on the adhesive alone.
Q. What is the difference between IP67 and IP68?
Under IEC 60529, IP67 means the enclosure is dust-tight and protected against the effects of temporary immersion, typically tested at about 1 m depth for 30 minutes. IP68 covers continuous immersion under conditions agreed between the manufacturer and the user, which must be more severe than IP67. An IP68 claim therefore always needs the stated depth and duration.
Q. Does an adhesive have an IP rating?
No. An IP rating applies to a finished enclosure or assembly tested under IEC 60529 or a related standard, not to an adhesive or raw material. Adhesive suppliers can provide material data such as adhesion, water absorption and temperature resistance, but the IP rating must be confirmed by testing the complete part.
Q. Why do sealed parts start leaking after thermal cycling?
Different materials expand and contract at different rates. Repeated heating and cooling can open microscopic gaps at the interface between the molding material and the housing or cable jacket, and pressure changes inside the part can then pull moisture in. Testing parts after thermal cycling, as well as when new, shows whether the seal will last.
Q. Can SILVERSTAR CHEMICAL supply polyamide for waterproof low pressure molding?
SILVERSTAR CHEMICAL manufactures solvent-free polyamide hot melts under the ERAMID brand for low pressure molding of PCBs, sensors, connectors and wire harnesses, including UL 94 V-0 flame-retardant grades and grades with thermal stability up to 200°C. Grade selection and available data are provided on inquiry.
If you are planning waterproof electronics encapsulation with hot melt, send us the target IP rating, the materials of the board, housing and cable jacket, the operating temperature range and your current molding setup. We will review suitable ERAMID grades and the data available. Contact our technical team · Tel +82-55-337-8841 · snschem@snschem.kr

